Alpha Data ADM-XRC-9R1 Скачать руководство пользователя страница 21

Страница: 21 / 38

ADM-XRC-9R1 User Manual
V1.7 - 16th Sept 2020

3.5 Zynq PS Block

3.5.1 Boot Modes

BootMode0
(SW1-1)

BootMode1
(SW1-2)

BootMode2
(SW1-3)

BootMode3

(SW1-4)

Boot Mode

JTAG

OFF

Quad SPI

OFF

SD Flash

Reserved

Table 14 : Boot Mode Selection

3.5.2 Quad SPI Flash Memory

1Gb Flash Memory (2x Micron MT25QU512AB) is used for storing executable code and data for the PS and PL,

such as a bootloader, operating system and bitstream.

The flash memory can only be accessed by the PS.

Utilities for erasing, programming and verification of the flash memory are available in Linux.

Write Protect

The Flash Write Protect (WP#) pin is connected to an inverted version of the NVMRO signal at the XMC

interface. When the NVMRO signal is active (High), all writes to the flash will be inhibited. This state will be

indicated by the Amber LED as shown in

LED Locations

3.5.3 MicroSD Flash Memory

A MicroSD card is used for storing executable code and data for the PS and PL, such as a bootloader, operating

system and bitstream.

The flash memory can only be accessed by the PS.

3.5.4 PS DDR4 Memory

The ADM-XRC-9R1 is fitted with one bank of PS DDR4 SDRAM. The bank is made up of a two 16-bit wide

memory devices in parallel to provide a 32-bit datapath capable of running up to 1200MHz (DDR4-2400). 8Gbit

devices (Micron MT40A512M16HA-083) are fitted as standard to provide 2GByte of memory.

Full details of the interface, signaling standards and an example design are provided in the ADM-XRC-9R1

example design.

3.5.5 PS MGT Links

There are a total of 4 MGT links connected to the PS Multi-Gigabit Transceivers. See

MGT Links

for further

details

Page 15

Functional Description
ad-ug-1353_v1_7.pdf

Содержание ADM-XRC-9R1







































Результаты поиска

Содержание ADM-XRC-9R1

Отзывы:

Похожие инструкции для ADM-XRC-9R1

Бренды по названию

Популярные бренды

Alpha Data ADM-XRC-9R1, Руководство пользователя

Результаты поиска

Содержание ADM-XRC-9R1

Отзывы:

Похожие инструкции для ADM-XRC-9R1

Бренды по названию

Популярные бренды