AllSportSystems SUPERBAY 10W x 9H Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 48

AllSportSystems SUPERBAY 10W x 9H Скачать руководство пользователя страница 40

All

SportSystems, Inc.

©

2020.

Step 2 - Add eye and trim cable to proper length

Complete cable assembly by first determining the proper length of the cable, forming the eye and then
trimming off extra cable. Follow the steps below …

(1)

Open Turnbuckle

fully as

shown below. This is important
for providing tension on the
cable after it is attached to the
cable.

(2)

For

SideRite™ Cables

,

wrap cable around the top and
then the bottom depth poles for
each SideRite™ Cables. Pull
the end of the cable through
the hooked end of the
turnbuckle until cable is tight.
Mark the cable to indicate
where the eye should be
formed.

(3)

For

ShotDefender™

Cables

, wrap cable around the

top-left and top-right depth
poles (across entire width). Pull
the end of the cable through
the hooked end of the
turnbuckle until cable is tight.
Mark the cable to indicate
where the eye should be
formed.

(4)

Thread two wire clips on to

the cable and form a loop in the
cable around the hook end of
the turnbuckle.

(5)

Thread the dead end of the

cable back through the wire
clips. Tighten wire clips with
wrench.

(6)

TRIM extra cable and

tighten turnbuckle to provide
tension on the cable.

Page 40 of 48

Return to Table of Contents

February 3, 2020

«
...
38
39
40
41
42
...
»

Содержание SUPERBAY 10W x 9H

















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды