Allnet ALL168205NANO Скачать руководство пользователя страница 9

Страница: 9 / 11

LEDs

PWR

(Red)

On: Power on

Blinking: Standby mode (*1)

Off: Power off

PLC

(Green/Orange/Red)

On: Powerline Link detected and no traffic

Blinking: Powerline traffic detected



Green: The Powerline connection quality is good



Orange: The Powerline connection quality is fair



Red: The Powerline connection quality is bad

Off: No Powerline Link detected

ETH

(Green)

On: Ethernet Link detected

Blinking: Ethernet traffic detected

Off: No Ethernet Link detected

*1 :

The “PWR“ LED indicator will blink in standby mode. It will automatically get into standby mode, if

the Ethernet-link is lost for 60 seconds. If you unplug the Ethernet cable, it will get into standby

mode after 60 seconds.

Under standby mode, PLC- and ETH-LEDs will both be off.

Содержание ALL168205NANO











Результаты поиска

Содержание ALL168205NANO

Отзывы:

Похожие инструкции для ALL168205NANO

Бренды по названию

Популярные бренды

Allnet ALL168205NANO, Быстрое руководство по установке

Результаты поиска

Содержание ALL168205NANO

Отзывы:

Похожие инструкции для ALL168205NANO

Бренды по названию

Популярные бренды