Allied 96G1DFE Скачать руководство пользователя

Страница: 46 / 53

507769-04

Page 46 of 53

Issue 1927

Planned Service

A service technician should check the following items during an annual inspection. Power to the unit must be shut off for

safety.

Fresh air grilles and louvers

(on the unit and in the

room where the furnace is installed) - Must be open and

unobstructed to provide combustion air.

Burners

- Must be inspected for rust, dirt, or signs of water.

Vent pipe

- Must be inspected for signs of water, cracked,

damaged or sagging pipe, or disconnected joints.

Unit appearance

- Must be inspected for rust, dirt, signs of

water, burnt or damaged wires, or components.

Blower access door

- Must be properly in place and

provide a seal between the return air and the room where

the furnace is installed.

Return air duct

- Must be properly attached and provide

an air seal to the unit.

Operating performance

- Unit must be observed during

operation to monitor proper performance of the unit and

the vent system.

Combustion gases

- Flue products must be analyzed and

compared to the unit specifications.

Problems detected during the inspection may make it

necessary to temporarily shut down the furnace until the

items can be repaired or replaced.

Instruct the homeowners to pay attention to their

furnace.

Situations can arise between annual furnace

inspections that may result in unsafe operation. For

instance, items innocently stored next to the furnace may

obstruct the combustion air supply. This could cause

incomplete combustion and the production of carbon

monoxide gas.

6. Remove four screws which secure burner box

assembly to vest panel. Remove burner box from the

unit.

7. Use the soft brush attachment on a vacuum cleaner

to gently clean the face of the burners. Visually

inspect the inside of the burners and crossovers for

any blockage caused by foreign matter. Remove any

blockage.

8. Reconnect the sensor wire and reconnect the 2 pin

plug to the ignitor wiring harness.

9. Reinstall the burner box assembly using the existing

four screws. Make sure that the burners line up in the

center of the burner ports.

10. Reinstall the gas valve manifold assembly. Reconnect

the gas supply line to the gas valve. Reinstall the

burner box cover.

11. Reconnect 2 pin plug to gas valve.
12. Replace the blower compartment access panel.
13.

Refer to instruction on verifying gas and electrical

connections when re-establishing supplies.

14. Follow lighting instructions to light and operate furnace

for 5 minutes to ensure that heat exchanger is clean

and dry and that furnace is operating properly.

15. Replace heating compartment access panel.

Содержание 96G1DFE






















































Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды

Allied 96G1DFE, Руководство по установке

Результаты поиска

Содержание 96G1DFE

Отзывы:

Похожие инструкции для 96G1DFE

Бренды по названию

Популярные бренды