Allied 95G1UHE Скачать руководство пользователя

Страница: 21 / 59

508093-01

Issue 2033

Page 21 of 59

Figure 16.

Multi−Meter

(set to VAC)

P48

P49

120

Turn on power to unit. Check for 120 volts across terminals

“L” and “N” on input plug P48. If voltage is present continue

upstream of plug P48. Proceed to test 3.

Multi−Meter

(set to VAC)

P48

P49

Switch thermostat to CONTINUOUS FAN MODE. Check for

24 volts across terminal “C” on input plug P48and speed tap

used for continuous fan. (1, 2, 3, 4 or 5) on input plug P49. If

24 volts is not present problem may be up stream of plug P49.

Proceed to test 4.

Multi−Meter

(set to VAC)

Multi−Meter

(set to VAC)

problem is with the harness. If voltage is not present,

problem may be may be with the integrated control.

Check for 120 volts across terminals “CIRC” and “Neutrals”

on the integrated control. If voltage is present, problem is

with the harness. If voltage is not present problem may be

may be with the integrated control.

Test 1

Test 2

Test 3 (if necessary)

Test 4 (if necessary)

to test 2. If voltage is not present, problem may be

Check for 24 volts across terminals “24 COM” and “FAN”

terminals on the integrated control. If voltage is present,

Содержание 95G1UHE




























































Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды

Allied 95G1UHE, Руководство по обслуживанию

Результаты поиска

Содержание 95G1UHE

Отзывы:

Похожие инструкции для 95G1UHE

Бренды по названию

Популярные бренды