Allied 80G2UHE Скачать руководство пользователя

Страница: 20 / 42

508144-01

Page 20 of 42

Issue 2128

Removal of the Furnace from Common Vent

In the event that an existing furnace is removed from

a venting system commonly run with separate gas

appliances, the venting system is likely to be too large to

properly vent the remaining attached appliances.

Conduct the following test while each appliance is operating

and the other appliances (which are not operating) remain

connected to the common venting system. If the venting

system has been installed improperly, you must correct the

system as indicated in the general venting requirements

section.

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being

placed into operation could result in carbon monoxide

poisoning or death.

WARNING

The following steps shall be followed for each appliance

connected to the venting system being placed into

operation, while all other appliances connected to the

venting system are not in operation:

1. Seal any unused openings in the common venting

system.

2. Inspect the venting system for proper size and

horizontal pitch. Determine that there is no blockage,

restriction, leakage, corrosion, or other deficiencies

which could cause an unsafe condition.

3. Close all building doors and windows and all doors

between the space in which the appliances remaining

connected to the common venting system are located

and other spaces of the building. Turn on clothes

dryers and any appliances not connected to the

common venting system. Turn on any exhaust fans,

such as range hoods and bathroom exhausts, so they

will operate at maximum speed. Do not operate a

summer exhaust fan. Close fireplace dampers.

4. Follow the lighting instructions. Turn on the appliance

that is being inspected. Adjust the thermostat so that

the appliance operates continuously.

5. After the burners have operated for 5 minutes, test for

leaks of flue gases at the draft hood relief opening.

Use the flame of a match or candle.

6. After determining that each appliance connected to

the common venting system is venting properly, (step

3) return all doors, windows, exhaust fans, fireplace

dampers, and any other gas burning appliances to

their previous mode of operation.

7. If a venting problem is found during any of the preceding

tests, the common venting system must be modified

to correct the problem. Resize the common venting

system to the minimum vent pipe size determined by

using the appropriate tables in Appendix G. (These

are in the current standards of the National Fuel Gas

Code ANSI 2223.1.

Gas Piping

If a flexible gas connector is required or allowed by

the authority that has jurisdiction, black iron pipe shall

be installed at the gas valve and extend outside the

furnace cabinet. The flexible connector can then be

added between the black iron pipe and the gas supply

line.

CAUTION

Do not over torque (800 in-lbs) or under torque (350

in-lbs) when attaching the gas piping to the gas valve.

WARNING

FIELD

PROVIDED

AND INSTALLED

Left Side Piping

(Standard)

Right Side Piping

(Alternate)

GROUND

JOINT

UNION

DRIP LEG

MANUAL

MAIN SHUT-OFF

VALVE

AUTOMATIC

GAS VALVE

(with manual

shut-off valve)

GROUND

JOINT

UNION

DRIP LEG

MANUAL

MAIN SHUT-OFF

VALVE

AUTOMATIC

GAS VALVE

(with manual

shut-off valve)

NOTE:

BLACK IRON PIPE

ONLY

TO BE ROUTED INSIDE OF CABINET

Figure 27.

Possible Gas Piping Configurations - Upflow Applications

Содержание 80G2UHE











































Результаты поиска

Содержание 80G2UHE

Отзывы:

Похожие инструкции для 80G2UHE

Бренды по названию

Популярные бренды

Allied 80G2UHE, Руководство по установке

Результаты поиска

Содержание 80G2UHE

Отзывы:

Похожие инструкции для 80G2UHE

Бренды по названию

Популярные бренды