Allied 80G2DFE страница 39 Скачать руководство пользователя

Страница: 39 / 42

508189-01

Issue 2116

Page 39 of 42

Troubleshooting: Heating Sequence of Operation (Continued)

HEATING SEQUENCE OF OPERATION

LOW FLAME SIGNAL

(Does not affect control operation)

STATUS ERROR CODE 1 + 2.

FLAME SIGNAL ABOVE

( 1.40 microamps)

YES

CONTINUED ON NEXT PAGE

YES

SINGLE-STAGE THERMOSTAT MODE

(DIP SWITCH SET AT “ON”)

TWO STAGE THERMOSTAT MODE

(DIP SWITCH SET AT “OFF”)

YES

START SECOND-STAGE RECOGNITION

ON DELAY (10 OR 15 MINUTES).

STATUS LED -- HEARTBEAT

45-SECOND INDOOR BLOWER ON DELAY BEGINS.

STATUS LED -- HEARTBEAT.

YES

PRIMARY & SECONDARY LIMIT SWITCHES

CLOSED?

GAS VALVE OFF, COMBUSTION AIR INDUCER OFF,

INDOOR BLOWER ON.

STATUS ERROR CODE 3 + 1.

HAS PRIMARY OR SECONDARY LIMIT

SWITCH CLOSED WITHIN 3 MINUTES?

(Indoor blower on low speed during 3-minute period)

FIRST-STAGE (LOW FIRE)

PRESSURE SWITCH CLOSED?

LIMIT SWITCH WATCHGUARD MODE.

GAS VALVE OFF, COMBUSTION AIR INDUCER OFF,

INDOOR BLOWER OFF WITH DELAY.

STATUS ERROR CODE 4 + 5

IS 60-MINUTE RESET PERIOD COMPLETE?

THERMOSTAT CALLS FOR HEAT.

STATUS LED -- HEARTBEAT.

SEE BOX A.

YES

GAS VALVE OFF. COMBUSTION AIR INDUCER ON.

INDOOR BLOWER OFF AFTER DELAY.

STATUS ERROR CODE 2 + 3. CONTROL RESTARTS

IGNITION SEQUENCE IF PRESSURE SWITCH

CLOSES WITHIN 2-1/2 MINUTES.

YES

FIRST-STAGE HEAT DEMAND SATISFIED?

GAS VALVE OFF, COMBUSTION AIR INDUCER

OFF FOLLOWING POST PURGE.

INDOOR BLOWER OFF WITH DELAY

STATUS LED -- PULSE

YES

SECOND-STAGE HEAT DEMAND.

SECOND-STAGE HEAT DEMAND REQUIRED?

SECOND STAGE PRESSURE SWITCH CLOSED?

ABNORMAL FLASH CODE.

NOTE - IF SECOND-STAGE PRESSURE SWITCH

WAS ORIGINALLY FOUND CLOSED,

ABNORMAL CODE WILL FLASH.

SECOND-STAGE PRESSURE SWITCH CLOSED

AT BEGINNING OF HEAT DEMAND?

STATUS ERROR CODE 2 + 6.

YES

SECOND-STAGE 30-SECOND DELAY ON BEGINS.

STATUS LED -- HEARTBEAT.

SECOND-STAGE COMBUSTION AIR INDUCER

ON. SECOND-STAGE GAS VALVE ON. HIGH

HEAT INDOOR BLOWER SPEED ON.

STATUS LED -- HEARTBEAT.

YES

SECOND-STAGE PRESSURE SWITCH CLOSED

IN LESS THAN TEN (10) SECONDS?

STATUS LED -- HEARTBEAT

YES

RETURNS TO FIRST-STAGE HEAT MODE WHICH

CONTINUES UNTIL SECOND-STAGE PRESSURE

SWITCH CAN BE PROVEN or HEAT DEMAND IS

SATISFIED. FIVE (5) MINUTE WAIT PERIOD

INITIATED BEFORE RETRY. WERE 5 ATTEMPTS

MADE FOR SECOND-STAGE HEAT?

YES

CONTINUES FIRST-STAGE HEATING DEMAND.

WILL NOT REATTEMPT SECOND-STAGE

HEATING DEMAND.

STATUS ERROR CODE 2 + 5.

SECOND STAGE HEAT DEMAND

STATUS LED -- HEARTBEAT.

YES

CONTINUED

GAS VALVE OFF. COMBUSTION AIR INDUCER ON.

INDOOR BLOWER ON.

STATUS ERROR CODE 5 + 1. SEQUENCE HOLDS

UNTIL ROLLOUT SWITCH IS RESET AND MAIN

POWER IS INTERRUPTED OR THERMOSTAT

IS CYCLED OFF/ON FOR 3 SECOND MINIMUM.

ROLLOUT SWITCHES CLOSED?

YES

Содержание 80G2DFE











































Результаты поиска

Содержание 80G2DFE

Отзывы:

Похожие инструкции для 80G2DFE

Бренды по названию

Популярные бренды

Allied 80G2DFE, Руководство по обслуживанию

Результаты поиска

Содержание 80G2DFE

Отзывы:

Похожие инструкции для 80G2DFE

Бренды по названию

Популярные бренды