Allied 80G1UHEX Series Скачать руководство пользователя

Страница: 18 / 32

507651-01

Page 18 of 32

Issue 1907

Gas Piping

Gas supply piping should not allow more than 0.5”W.C.

drop in pressure between gas meter and unit. Supply gas

pipe must not be smaller than unit gas connection.

If a flexible gas connector is required or allowed by

the authority that has jurisdiction, black iron pipe shall

be installed at the gas valve and extend outside the

furnace cabinet. The flexible connector can then be

added between the black iron pipe and the gas supply

line.

CAUTION

Gas Supply

Do not over torque (800 in-lbs) or under torque (350

in-lbs) when attaching the gas piping to the gas valve.

WARNING

1. This unit is shipped standard for left or right side

installation of gas piping (or top entry in horizontal

applications). Connect the gas supply to the piping

assembly.

2. When connecting the gas supply piping, consider

factors such as length of run, number of fittings, and

furnace rating to avoid excessive pressure drop. Table

6 lists recommended pipe sizes for typical applications.

3. The gas piping must not run in or through air ducts,

clothes chutes, gas vents or chimneys, dumb waiters,

or elevator shafts.

4. The piping should be sloped 1/4 inch (6.4 mm) per

15 feet (4.57 m) upward toward the meter from the

furnace. The piping must be supported at proper

intervals [every 8 to 10 feet (2.44 to 3.01 m)] with

suitable hangers or straps. Install a drip leg in vertical

pipe runs to the unit.

5. A 1/8” N.P.T. plugged tap or pressure post is located

on the gas valve to facilitate test gauge connection.

See Figure 18.

6. In some localities, codes may require the installation

of a manual main shut off valve and union (furnished

by the installer) external to the unit. The union must be

of the ground joint type.

Removal of the Furnace from Common Vent

In the event that an existing furnace is removed from

a venting system commonly run with separate gas

appliances, the venting system is likely to be too large to

properly vent the remaining attached appliances.

Conduct the following test while each appliance is operating

and the other appliances (which are not operating) remain

connected to the common venting system. If the venting

system has been installed improperly, you must correct the

system as indicated in the general venting requirements

section.

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each

appliance connected to the venting system being

placed into operation could result in carbon monoxide

poisoning or death.

CAUTION

The following steps shall be followed for each appliance

connected to the venting system being placed into

operation, while all other appliances connected to the

venting system are not in operation:
1. Seal any unused openings in the common venting

system.

2. Inspect the venting system for proper size and

horizontal pitch. Determine that there is no blockage,

restriction, leakage, corrosion, or other deficiencies

which could cause an unsafe condition.

3. Close all building doors and windows and all doors

between the space in which the appliances remaining

connected to the common venting system are located

and other spaces of the building. Turn on clothes

dryers and any appliances not connected to the

common venting system. Turn on any exhaust fans,

such as range hoods and bathroom exhausts, so they

will operate at maximum speed. Do not operate a

summer exhaust fan. Close fireplace dampers.

4. Follow the lighting instructions. Turn on the appliance

that is being inspected. Adjust the thermostat so that

the appliance operates continuously.

5. After the burners have operated for 5 minutes, test for

leaks of flue gases at the draft hood relief opening.

Use the flame of a match or candle.

6. After determining that each appliance connected to

the common venting system is venting properly, (step

3) return all doors, windows, exhaust fans, fireplace

dampers, and any other gas burning appliances to

their previous mode of operation.

7. If a venting problem is found during any of the

preceding tests, the common venting system must be

modified to correct the problem.

Resize the common venting system to the minimum vent

pipe size determined by using the appropriate tables in

Appendix G. These are in the current standards of the

National Fuel Gas Code ANSI 2223.1.

Содержание 80G1UHEX Series

































Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды

Allied 80G1UHEX Series, Руководство по установке

Результаты поиска

Содержание 80G1UHEX Series

Отзывы:

Похожие инструкции для 80G1UHEX Series

Бренды по названию

Популярные бренды