background image

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches

39

Patch SB251-13 for Software Release 2.5.1
C613-10361-00 REV M

 

Each new entry into the IP routing table resulted in an ARP request being 
sent to resolve the next hop address. To prevent ARP flooding, a limit of 6 
simultaneous ARP requests are transmitted.

 

Changing a port’s VLAN tagging was not updating the L3 multicasting 
entries for that port. This issue has been resolved.

A log message is now created when a user is forced to logout from an 
asynchronous port when another user (i.e. someone connected via Telnet) 
resets the asynchronous connection with the RESET ASYN command.

After VRRP was enabled, the link status of the switch ports was shown as 
UP, even if there was no connection to the ports. This issue has been 
resolved.

 

Broadcast storm control (BCSC) rate limiting was not operating on 
broadcast packets when set per VLAN. This issue has been resolved.

STP ignores some BPDU packets coming in on tagged ports. This issue has 
been resolved. Now the VLAN tag is ignored on all devices except Rapier

Series Switches with multiple STPs on the receiving port.

Multicast Listener Discovery (MLD) was not setting the filter mode 
correctly when receiving certain packet types whilst in EXCLUDE mode. 
This issue has been resolved.

Entering a “?” on the command line, now displays the correct list of 
available options.

The RESET IP COUNTER=ALL command was not working correctly when 
issued from the command line. This issue has been resolved.

Sometimes the 

Agent Address

 field in SNMP traps was not the same as the 

IP source address. This meant that sometimes the NMS did not send an 
alarm to the network manager when traps were received from switches. 
This issue has been resolved.

When there were a large number of BGP routes, the SHOW BGP ROUTE 
command sometimes caused an error. This issue has been resolved.

PCR: 03329

Module: IPG

                                Level: 2

PCR: 03331

Module: SWI, VLAN

                                 Level: 2

PCR: 03332

Module: TTY

                                  Level: 4

PCR: 03333

Module: IPG

                                  Level: 3

PCR: 03335

Module: SWI

                                  Level: 2

PCR: 03341

Module: STP

                                  Level: 3

PCR: 03342

Module: IPV6

                               Level: 3

PCR: 03343

Module: UTILITY

            Level: 4

PCR: 03345

Module: IPG

                                  Level: 4

PCR: 03346

Module: SNMP

                                  Level: 4

PCR: 03349

Module: BGP

                                  Level: 3

Содержание SB251-13



































































Отзывы: