background image

34

Patch Release Note

Patch SB251-13 for Software Release 2.5.1

C613-10361-00 REV M

If a DVMRP interface was deleted and then added again, DVMRP routes 
associated with this interface were not reactivated. This issue has been 
resolved.

If the RP candidate advertising time was set to a non-default value with the 
ADVINTERVAL parameter in the SET PIM command, the hold time in the 
message was not being updated correctly. This issue has been resolved.

The output from the SHOW SWITCH PORT COUNTER command was 
showing incorrect values for packets greater than 1519 bytes. This issue has 
been resolved.

If an IP address was added using the AD IP INTERFACE IP=DHCP and the 
server could not assign an IP address due to a network problem affecting 
the server’s VLAN, any further frames transmitted to IP addresses on other 
VLANS would be blocked. This issue has been resolved.

Previously, the default output of the SHOW SWITCH FDB command 
displayed the forwarding database information for ports on the controller 
card located in bay A. The default now displays all external ports for switch 
instances except for those on the controller card. This command no longer 
displays information about internal ports.

Zmodem was not naming some loaded files. This issue has been resolved.

STP was advertising an incorrect length for BPDU packets. This issue has 
been resolved.

Values for the KEEPALIVE and HOLDTIME parameters in the ADD BGP 
PEER and SET BGP PEER commands were not interacting correctly. This 
issue has been resolved.

The PURGE IP command did not remove ENABLE IP IGMP from the 
configuration. This issue has been resolved.

IGMP queries were being sent after IGMP was disabled. This issue has been 
resolved.

RIP 

Request

 packets for IPv4 were not being transmitted when the link came 

up or when the switch restarted. This issue has been resolved.

PCR: 03222

Module: PIM, PIM6

                                  Level: 2

PCR: 03223

Module: SWI

                                  Level: 2

PCR: 03224

Module: IPG

                                  Level: 2

PCR: 03227

Module: SWI

                                  Level: 4

PCR: 03229

Module: LOAD

                                  Level: 3

PCR: 032231

STP

                                 Level: 3

PCR: 03232

Module: BGP

                                  Level: 3

PCR: 03234

Module: IPG

                                  Level: 3

PCR: 03236

Module: IPG

                                  Level: 3

PCR: 03237

Module: IPG

                                  Level: 2

Содержание SB251-13



































































Отзывы: