Allied Telesis Broadcom Advanced Control Suite 3 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 80

Allied Telesis Broadcom Advanced Control Suite 3 Скачать руководство пользователя страница 74

Chapter 2: Configuring Teaming

74

Deleting a VLAN

To delete a VLAN in Expert Mode, do the following:

1. Click the

Team Management

button at the bottom of the BACS 3

window, or from the

View

menu, select

Navigate

, then

Team

Management

.

2. Select the VLAN to delete.

3. From the

Teams

menu, select

Remove VLAN

.

4. Click

Apply

.

5. Click

Yes

when the message is displayed indicating that the network

connection will be temporarily interrupted.

Note

If you delete a team, any VLANs configured for that team are also
deleted.

Configuring

LiveLink

LiveLink is a feature of BASP that is available for the Smart Load
Balancing (SLB) and SLB (Auto-Fallback Disable) type of teaming. The
purpose of LiveLink is to detect link loss beyond the switch and to route
traffic only through team members that have a live link.

Read the following notes before you attempt to configure LiveLink.

Note

Before you configure LiveLink, review the description of the LiveLink
feature. Also verify that each probe target you plan to specify is
available and working. If the IP address of the probe target changes,
you must reconfigure LiveLink. If the MAC address of the probe
target changes, you must restart the team.

Note

A probe target must be on the same subnet as the team, have a
valid statically-assigned IP address, (not a broadcast, multicast, or
unicast) and be highly available (always on).

Note

To ensure network connectivity to the probe target, ping the probe
target from the team.

«
...
72
73
74
75
76
...
»

Содержание Broadcom Advanced Control Suite 3

















































































Отзывы:

Нет отзывов