Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 75 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Feature Licenses

The x930 Switches comes with the AlliedWare Plus operating system and

a base set of features that are available as soon as you install the devices.

Allied Telesis provides additional features in the AlliedWare Plus software

for the switches, but they have to be unlocked before you can use them.

They are unlocked with feature licenses from Allied Telesis. Refer to the

product’s data sheet on the Allied Telesis web site for the list of licenses.

Here are the guidelines to feature licenses for a stack of x930 Series

switches:



The VCStack feature is part of the base features of the switches. It

does not require a feature license.



You may install feature licenses while the switches are operating

as stand-alone units or as a stack.



Depending on the feature license, you might have to order one

license for each switch or one license for the entire stack.



The switches will form a stack even if they have different feature

licenses. However, the additional features are only available on

those switches that have the necessary licenses. The stack

generates a warning message if it detects that the switches do not

have the same optional feature licenses.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды