Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 73

Страница: 73 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

Master and Member Switches

Stacks have a master switch. Some of its functions include:



Coordinate and monitor stack operations.



Verify that the switches are using the same version of

management software.



Verify that the switches have different ID numbers. It automatically

assigns new ID numbers to resolve situations where two or more

switches have the same ID number.



Verify that the stacking transceivers that connect the switches

together are cabled correctly.

The other switches are called member switches. A member switch can

automatically transition to the master role if the current master switch is

removed from the stack or powered off. This ensures continued operations

of the stack even if the master switch stops operating.

Selection of the

Master Switch

The switches of the stack designate the master switch during the

initialization process that they perform whenever they are powered on or

reset. They select the master switch based on the following parameters:



Stack priority numbers



MAC addresses

The stack priority number is an adjustable value of 0 to 255, where the

lower the number, the higher the priority. Typically, the switch with the

lowest priority number (highest priority) becomes the master switch of a

stack. The default priority value is 128.

If the switches have the same priority values, they select the master switch

based on their MAC addresses. As with the priority value, the lower the

MAC address, the higher the priority. The switch with the lowest MAC

address becomes the master switch.

If you power on the switches of the stack simultaneously without adjusting

the priority values, they select the master switch based on their MAC

addresses. If you power on the switches one at a time, the master switch

is the first switch to be powered on.

After the stack is established and operating, you may change the priority

settings on the individual units and so control which switch will be the

master switch the next time you reboot or power on the stack.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды