Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 52

Страница: 52 / 214

Chapter 1: Overview

Console Port

You use the Console port to manage the switch and configure its features

and parameter settings. This type of management uses serial RS-232 and

is commonly referred to as local management because it is not conducted

over your network. To perform local management, you must be at the

location of the switch and use the management cable included with the

device.

To establish a local management session with the switch, connect a

terminal or a personal computer with a terminal emulation program to the

Console port, which has an RJ-45 style (8P8C) connector, using the

provided management cable. The cable has RJ-45 style (8P8C) and DB-9

(D-sub 9-pin) connectors.

To connect a laptop/desktop computer and a network device, such as a

switch, you can use the AT-VT-Kit3 management cable. The cable is a

USB-to-Serial converter with a USB-A male connector on one end and an

RJ-45 female receptor on the other end.

Note

To use the AT-VT-Kit3 management cable, you must install the

driver software onto your Windows system. For installation

instructions, refer to Allied Telesis

Quick Installation Guide AT-VT-

Kit3 Management Cable.

The Console port is set to the following specifications:



Default baud rate: 9600 bps (Range is 9600 to 115200 bps)



Data bits: 8



Parity: None



Stop bits: 1



Flow control: None

Note

These settings are for a DEC VT100 or ANSI terminal, or an

equivalent terminal emulation program.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды