Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 37

Страница: 37 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

level only receive power if all of the ports assigned to the other two levels

are already receiving power. As with the other levels, if there is not enough

power to support all of the ports set to the Low priority level, power is

provided to the ports based on port number, in ascending order.

Power allocation is dynamic. Ports supplying power to powered devices

may cease power transmission if the switch’s power budget is at maximum

usage and new powered devices, connected to ports with higher priorities,

become active.

Wiring

Implementation

The IEEE 802.3af standard defines two methods for the delivery of DC

power over copper cable from a switch to the powered devices. These

methods, known as modes A and B, identify the wires within the cable that

carry the DC power from the switch to a powered device.

Copper cabling typically consists of eight wires. With 10Base-T and

100Base-TX devices, the wires connected to pins 1, 2, 3, and 6 on the RJ-

45 connectors carry the network traffic while the wires connected to pins 4,

5, 7, and 8 are unused. With 1000Base-T devices, all eight wires are used

to carry network data.

It takes four wires to deliver DC power to a PD. With Mode A, the power is

delivered on pins 1, 2, 3, and 6. These are the same pins in 10Base-T and

100Base-TX devices that carry the network data. With mode B, the power

is provided over the spare wires.

The ports on the AT-x930-28GPX and AT-x930-52GPX Switches deliver

the power using pins 1, 2, 3, and 6, which corresponds to mode A in the

IEEE 802.3af standard. Powered devices that comply with the IEEE

802.3af standard are required to support both power delivery methods.

Legacy devices that do not comply with the standard will work with the

switch if they are powered on pins 1, 2, 3, and 6.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды