Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 24

Страница: 24 / 214

Chapter 1: Overview

Note

SFP+ ports 27/S1 and 28/S2 on the 28-port switches and ports 51/

S1 and 52/S2 on the 52-port switches are initially configured as

stacking ports for the VCStack feature. You can use them as regular

Ethernet ports by disabling VCStack or by using other switch ports

for the stack trunk. For more information, refer to Chapter 2, “Virtual

Chassis Stacking” on page 57.

SFP+ S1 and S2

Stacking Ports

SFP+ ports 27/S1 and 28/S2 on the 28-port switches and ports 51/S1 and

52/S2 on the 52-port switches can be used either as regular networking

ports or as the trunk in the VCStack feature to build a stack of up to eight

switches. For more information, refer to the Chapter 2, “Virtual Chassis

Stacking” on page 57.

LEDs

Here are the port LEDs:



Link/activity and duplex mode LEDs for the copper ports on non-

PoE switches



Link/activity and PoE status LEDs for the copper ports on PoE

switches



Link/activity LEDs for SFP and SFP+ ports



Stack ID number LED



eco-friendly button turns off the LEDs to conserve electricity

Installation

Options

Here are the installation options for the switches:



19-inch equipment rack



Desk or tabletop



Wall

MAC Address

Table

Here are the basic features of the MAC address tables of the switches:



Storage capacity of 64K dynamic and static entries



Automatic learning and aging

Management

Software and

Interfaces

Here are the management software and interfaces:



AlliedWare Plus Management Software



Command line interface



Web browser interface

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды