Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 146 / 214

Chapter 10: Displaying the AlliedWare Plus Version Number

146

7. Do one of the following:



If you need to upgrade the software on the switch, refer to the

Software Reference for x930 Series Switches, AlliedWare

Operating System

from

www.alliedtelesis.com



If you do not have to update the software, repeat the procedures in

this chapter on the remaining switches of the stack.

8. If there are no further switches, power off all the switches.

9. Go to one of the following chapters:



Chapter 11, “Building the Stack with SFP+ Ports S1 and S2” on

page 147



Chapter 12, “Building the Stack with AT-StackQS Cards” on page

159



Chapter 13, “Building the Stack with Copper or SFP Gigabit Ports”

on page 165

Table 20. Hardware Options and Management Software Versions

Optional Hardware

Minimum Version of Operating

System

AT-StackQS Card and AT-

QSFPICU Cables

5.4.5

AT-StackQS Card and AT-

QSFPSR Transceivers

5.4.5-1

AT-StackQS Card and AT-

QSFPLR4 Transceivers

5.4.5-2

AT-x9EM/XT4 Card

5.4.5-2

Stack trunks of copper or SFP

Gigabit ports

5.5.1-2.1

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды