Allied Telesis AT-x930-28GPX Скачать руководство пользователя страница 116

Страница: 116 / 214

Chapter 7: Installing the Switch in an Equipment Rack

116

Required Items

This procedure requires the following items:



Two equipment rack brackets (included with the switch)



Eight bracket screws (included with the switch)



Cross-head screwdriver (not provided)



Four standard equipment rack screws (not provided)

Note

The switch comes with four equipment rack brackets and sixteen

screws. Two brackets and eight screws are used to install the unit in

an equipment rack. The extra brackets and screws are for installing

the device on a wall.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды