Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 105 / 214

x930 Series Installation Guide for Virtual Chassis Stacking

105

Installing the Card

This section contains the procedure for installing AT-StackQS and AT-

x9EM/XT4 Cards in x930 Switches. The illustrations show the AT-

StackQS Card. The procedure is the same for the AT-x9EM/XT4 Card.

Note

Although the cards are hot-swappable, Allied Telesis recommends

powering off the switch before installing them because the

installation procedure requires temporarily removing the AT-FAN09

Fan Module.

Note

If the switch is powered on, power it off by performing step 1. If the

switch is already powered off, start with step 2.

To install the AT-StackQS or AT-x9EM/XT4 Card, perform the following

procedure:

1. If the switch is powered on, power it off by doing one of the following:



For the AC AT-PWR150, AT-PWR250, AT-PWR800, or AT-

PWR1200 Power Supply, disconnect the power cord from the AC

power source.



For the DC AT-PWR250-80 Power Supply, either turn Off the

power switch on the power supply or power off the DC circuit.

Warning

This unit might have more than one power cord. To reduce the risk

of electric shock, disconnect all power cords before servicing the

unit.



E30

2. Place the switch on a table, with the back panel facing you.

3. Loosen the two captive screws on the AT-FAN09 Fan Module with a

cross-head screwdriver. Refer to Figure 41 on page 106.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды