Allied Telesis AT-x930-28GPX Скачать руководство пользователя

Страница: 104 / 214

Chapter 5: Installing AT-StackQS and AT-x9EM/XT4 Cards

104

Guidelines

Please observe the following guidelines when handling AT-StackQS and

AT-x9EM/XT4 Cards.



Wear an anti-static device when handling the card.

Caution

The device can be damaged by electrostatic discharge (ESD). Be

sure to follow standard ESD protections procedures, such as

wearing a wrist or foot strap, when installing the device.



E106



Hold the card by its faceplate or edges.



Never touch the electronic components on the top or bottom of the

card.



Do not remove the card from its anti-static bag until you are ready

to install it in the switch.



If you need to remove the card from the switch, immediately return

it in its anti-static bag and packaging container.

Содержание AT-x930-28GPX























































































































































































































Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды

Allied Telesis AT-x930-28GPX, Руководство по установке

Результаты поиска

Содержание AT-x930-28GPX

Отзывы:

Похожие инструкции для AT-x930-28GPX

Бренды по названию

Популярные бренды