Allied Telesis AT-FAN08 Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 214

background image

AT-SBx908 GEN2 Installation Guide for Virtual Chassis Stacking

149

Viewing the AlliedWare Plus Version Number

Viewing the version numbers of the AlliedWare Plus operating software on
the switches before building the stack is important for the following
reasons:



The VCStack feature requires version 5.4.8-0 or later of the
AlliedWare Plus operating software. Switches with earlier versions
have to be updated.



The AT-XEM2-1CQ Line Card requires version 5.4.8-0 or later.



All switches in a stack must have the same operating software
version.

To view the version number of the operating software on the switch,
perform the following procedure:

1. Start a local management session on the switch. For instructions, refer

to “Starting a Local Management Session” on page 145.

2. In the User Exec mode, enter either the SHOW SYSTEM or SHOW

VERSION command.

3. Examine the Software Version field in the information the command

displays on your screen and do one of the following:



If the field says “548-0” or later, the AlliedWare Plus operating
software on the switch supports the VCStack feature. Go to the
next step.



If the field says “547”, the management software does not support
stacking. You must update the operating software on the switch to
the latest release before building the stack. For upgrade
instructions, refer to the Software Reference for SwitchBlade x908
GEN2 Series Switches on the Allied Telesis web site.

4. Write the version number of the operating software on paper. After

viewing the version numbers on all the switches, you will compare
them to confirm that all switches have the same version. If the switches
have different versions, you will have to update their operating
software before building the stack.

5. Go to “Viewing Optional Feature Licenses” on page 150

«
...
147
148
149
150
151
...
»

Содержание AT-FAN08























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AT-FAN08

Baseline 2226 Plus

Бренд: 3Com Страницы: 4

Бренд: Aastra Страницы: 12

Бренд: Aastra Страницы: 2

Sierra Video 1208V3S

Бренд: Kramer Страницы: 2

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: cable matters Страницы: 8

Бренд: A-Neuvideo Страницы: 15

KingShield T206-C

Бренд: Green Brook Страницы: 2

Бренд: Orbis Страницы: 2

Бренд: Lindy Страницы: 6

Бренд: KDS Страницы: 10

Бренд: DELTA DORE Страницы: 3

iMatrix H44H150

Бренд: infobit Страницы: 27

Бренд: Murphy Страницы: 24

Бренд: AV Access Страницы: 16

Бренд: N-Tron Страницы: 169

Бренд: EnGenius Страницы: 72

Бренд: Belkin Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды