ALLIANCE Metered Скачать руководство пользователя страница 45

Страница: 45 / 54

Operation

802702

Step 7: Start Dryer

To start dryer, push

START

keypad.

To stop dryer at any time, open the door. To restart the
dryer, close door and push

START

keypad.

Cycle is completed when time remaining reaches
00 minutes.

Figure 64

Indicator Lights

INSERT COINS/CARD

INSERT COINS/CARD

is lit to prompt the user to

insert coins or card to satisfy the vend price. When

INSERT COINS/CARD

is lit, the three digits and

decimal point will display the vend price remaining to
be satisfied.

START

START

is lit when the dryer is not in a cycle, the full

vend price has been satisfied and the dryer door is
closed. When the

START

keypad is pressed, the cycle

will begin or resume.

DRYING

DRYING

is lit to indicate that one of the heated cycles

(HIGH TEMP, MED TEMP, LOW TEMP) is currently
in operation.

DRYING

will turn off at the end of a

heated cycle or when the COOL DOWN cycle begins.

COOL DOWN

COOL DOWN

is lit whenever the COOL DOWN

portion of a heated cycle is active. It is also lit when
the NO HEAT cycle is in operation.

ADD TIME (Card Models Only)

ADD TIME

flashes when a card is inserted while a

cycle is running or when a card is left in the reader.

REMOVE CARD (Card Models Only)

REMOVE CARD

flashes when a card is inserted or left

in the reader after a transaction is complete. It will also
flash alternately with

ADD TIME

when a card is

inserted while a cycle is running or when a card is left
in the reader.

D778I

Содержание Metered























































Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды

ALLIANCE Metered, Руководство по установке и эксплуатации

Результаты поиска

Содержание Metered

Отзывы:

Похожие инструкции для Metered

Бренды по названию

Популярные бренды