Alliance Laundry Systems ZWC372-3059, Сервисная инструкция

Страница: 45 / 76

37987
43
Section 5 Service Procedures
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the washer before servicing.
• Never start the washer with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the washer is properly grounded.
W003
WARNING
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
38. HUB AND SEAL KIT ASSEMBLY
IMPORTANT: If water is present in washtub, spin
and pump out before removing drive bell.
a. Remove two screws from bottom edge of front
panel. Refer to Figure 25.
b. Pull bottom of panel away from washer until
hold-down clips (located on top flange of
panel) disengage from slots in cabinet top.
Refer to Figure 25.
c. Open loading door.
d. Remove agitator by placing two agitator hooks,
No. 254P4P, under bottom edge of agitator.
Refer to Figure 12.
IMPORTANT: Hooks should be positioned 180
degrees of each other, and must be placed under
agitator vanes for greater stability. If hooks are
placed between vane area, damage to agitator may
occur.
e. Using a rocking motion (back and forth)
carefully lift agitator off drive bell.
f. Hinge cabinet top or remove. Refer to
Paragraph 34.
g. Loosen hose clamp and remove filler hose from
outer tub cover. Refer to Figure 32.
NOTE: When reinstalling filler hose, white line on
hose must be aligned with line located on top side of
outer tub cover. Refer to Figure 32.
Tub Cover and Gasket:
(1) There are eight tub cover hold-down tabs
which snap over the outer tub flange. Using
special tub cover tool, Part No. 273P4,
insert two prongs of tool underneath each
side of tandem tabs. Refer to Figure 32. Tilt
tool toward center of tub cover and at the
same time lift upward on cover to unsnap
hold-down tabs from outer tub flange. One
by one, disengage each of the eight hold-
down tabs from outer tub flange and
remove cover.
(2) Lift cover off outer tub and set beside
washer cabinet.
IMPORTANT: When installing outer tub cover,
always use a new cover gasket.
NOTE: Clean and remove any foreign material in
gasket groove of outer tub cover and outer tub
flange.
(3) Starting at the positioning pin located
between the two bleach funnel outlet tabs,
lay gasket into gasket groove of tub cover.
Refer to Figure 33.
(4) Using your fingers, press gasket down into
gasket groove of tub cover. Avoid pressing
gasket past ends of hold-down tabs.
IMPORTANT: Care must be taken not to twist or
bunch gasket in any one area to avoid leaks after
assembly.
(5) Install gasket past ends of hold-down tabs
to bottom of gasket groove using semi-
curled end of tub cover tool Part No. 273P4.
NOTE: Tub cover tool Part No. 273P4 is designed to
spread open hold-down tabs to prevent tearing of
gasket during installation.
(6) With tub cover tilted at approximately a 45
degree angle, insert the positioning pin into
notch on outer tub flange. Refer to
Figure 34.
NOTE: The two bleach funnel outlet tabs must be
angled down toward inside wall of outer tub for
proper dispensing of bleach.
(7) Lower cover and push down firmly on top
of hold-down tabs next to positioning pin
until tabs snap over edge of outer tub
flange.
(8) Cross over to opposite side of tub cover and
push down firmly on top of hold-down tabs
until tabs snap over edge of outer tub
flange. Continue with this criss-cross
pattern, until tub cover is fully seated.
Visually check each tab area again to
ensure cover is seated.
(9) Check whether or not bleach drain tabs are
in the down position by looking through the