Alliance Laundry Systems IYG065J Скачать руководство пользователя | Manualshive

Страница: 79 / 106

background image

NOTE: The error message "Too Hot" can also appear at
the end of a cycle even if no failure has occurred as an
example, suppose a wash program with a hot wash. Af-
ter this hot wash sequence, no sequence with a low
water temperature has been programmed. At the end of
such a wash cycle, the temperature in the tub will stay
high even if there is no water in the tub. As a result the
wash computer will decide that it’s not safe to open the
door as the measured temperature inside the tub is too
high. Without inserting cold water inside the tub, it can
take a long time before the temperature drops to an ac-
ceptable safe level. Once the temperature in the drum
has dropped sufficiently, the failure message will dis-
appear and the door will be unlocked automatically.

DEPENDING ON THE FAILURE TYPE THE COMPUTER
WILL START A SPECIFIC PROCEDURE:

WHEN SAFETY IS INVOLVED

• Full stop + tumble: the program is stopped but will run the

tumble sequence.

• Full stop + safety time: the program is stopped and a safety

time is started.

• Don’t start: the program will not be started as long as the safe-

ty conditions are not fulfilled.

WHEN SAFETY IS NOT INVOLVED

• Full stop + request for continue: a request to "Continue ?" the

program is displayed.

• Skip + continue: the actual cycle step is skipped and the pro-

gram continues with the next step.

• Continue: the program continues.

SPECIAL CASES:

Fault 11: Fill Time Failure and Fault 14: Heating Time Failure:

• After overruling and erasing the failure message, you can re-

start or stop the sequence, as Continue ? will be displayed.

Possible cause:

• Water supply inlets closed.
• Decreasing capacity of the heating elements.

Fault 31: Initialization Fault Inverter and Fault 32: Verification
Fault Inverter:

• Indicate that the frequency inverter is not loaded with the cor-

rect parameter settings, the washing machine can be damaged
when the inverter is functioning with the wrong settings. Do
not use the washing machine before a technician has inspect-
ed the problem.

Fault 41: Service Due:

• Will occur over and over again until you have reset the cycle

counter. Refer to

as to how to reset the cycle

counter.

Failure Message Overview

Failure Message Overview

Num-

ber

Failure Mes-

sage

Failure

Action

Fault Occurrence

E2

No Drain

Drain failure

Full Stop + tumble

Draining sequence

E3

Tilt Fault

Safety switch activated

Full stop + tumble

Whole cycle, revolutions under
the distribution revolutions lev-
el.

E4

Imbalance

Safety switch activated during
the transition from distribution
into spin sequence.

Skip + continue

Spin

E5

Tilt High Sp

Out of balance : high spin

Full stop + safety time

>500 or 750 RPM

E6

Door Switch

Door switch failure

Full stop + safety time

Whole cycle

E7

Door Coil

Door lock failure

Full stop + safety time

Whole cycle

E8

Door Closed Start

Door close check at start failure Don’t start

At start up

E9

Door Unload

Door lock switch closed failure Don’t start

End cycle

Table 47

continues...

Troubleshooting

©

Copyright, Alliance Laundry Systems LLC -

DO NOT COPY or TRANSMIT

79

Part No. D1631ENR7

«
...
77
78
79
80
81
...
»

Содержание IYG065J











































































































Отзывы:

Нет отзывов

Похожие инструкции для IYG065J

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 12

Бренд: Kärcher Страницы: 24

3VK730XC - annexe 1

Бренд: BALAY Страницы: 24

Бренд: Annovi Reverberi Страницы: 10

Бренд: Admiral Страницы: 32

Auto-Washer 1100 AC170

Бренд: Hoover Страницы: 10

Бренд: Samsung Страницы: 64

Бренд: Smeg Страницы: 37

Monogram ZBD8920PSS

Бренд: GE Страницы: 32

Бренд: GE Страницы: 16

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды