Alliance Laundry Systems BWNBX2PP303AW01 Скачать руководство пользователя страница 63

Страница: 63 / 64

Motor Test Procedure

WARNING

To reduce the risk of electric shock, fire, explosion,
serious injury or death:
• Disconnect electric power to the washer before

servicing.

• Never start the washer with any guards/panels re-

moved.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to
ensure that the washer is properly grounded.

W003

IMPORTANT: Disconnect base wire harness plug from
motor.

WARNING

Disconnect electric power to washer before perform-
ing the following steps:

W188

Perform motor test procedures using an Ohm meter.

NOTE: Resistance readings slightly out of given ranges
may be due to meter conditions. These readings DO
NOT necessarily indicate motor failure.

Meter Connections

Reading Should Be

If Not

Ground to Each Other Terminal Open

Terminal shorted to ground

White to Yellow

Closed

Open thermal overload

Red to Brown

2-8 Ohms

Start winding open or resist-
ance too high or too low

Blue to White

1-2 Ohms

High speed winding (4 pole)
open or resistance too high or
too low

Violet to White

2.5 Ohms (approximate)

Low winding open; High speed
winding open; or resistance too
high or too low

“R” to Red

Closed

Open start (auxiliary) switch

“P” to Blue

Closed

Open start switch 4 pole wind-
ing

Tests 8, 9 and 10 are with motor centrifugal mechanism in the run position.

“R” to Red

Open

Start auxiliary switch

“P” to Blue

3 Ohms (approximate)

Refer to Blue to White and
Violet to White

“P” to Violet

Closed

Open low (6 pole) winding run
switch

Motor Test Procedure

DO NOT COPY or TRANSMIT

Part No. 204591EN

Содержание BWNBX2PP303AW01

































































Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BWNBX2PP303AW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды