Alliance Laundry Systems BWNBX2PP303AW01 Скачать руководство пользователя страница 57

Страница: 57 / 64

Adjustments

WARNING

To reduce the risk of electric shock, fire, explosion,
serious injury or death:
• Disconnect electric power to the washer before

servicing.

• Never start the washer with any guards/panels re-

moved.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to
ensure that the washer is properly grounded.

W003

Leveling Legs

1. Place a level on the cabinet top and check if the washer is lev-

el from side to side and front to back.

2. If washer is not level, tilt washer back to access the front lev-

eling legs. Loosen the locknuts and adjust legs by screwing
into or out of washer base.

3. Once adjusted, tilt the washer forward on front legs and lower

back down into position to set the rear self-leveling legs.

4. Washer must not rock. When washer is level and does not

rock, tighten locknuts securely against bottom of washer base.
If these locknuts are not tight, washer will not remain station-
ary during operation.

Improper installation or flexing of weak floor will cause exces-
sive vibration.

Do not slide washer across floor once the leveling legs have been
extended, as legs and base could become damaged.

NOTE: For areas with uneven floors, a No. 566P3
Adjustable Rear Leg Extension Kit is available as
optional equipment at extra cost.

TLW381S_SVG

Level

Locknut

Leveling Leg

Rubber Foot

Washer Base

Figure 12

Belt

No belt adjustment is required.

Adjustments

DO NOT COPY or TRANSMIT

Part No. 204591EN

Содержание BWNBX2PP303AW01

































































Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды

Alliance Laundry Systems BWNBX2PP303AW01, Руководство по устранению неисправностей

Результаты поиска

Содержание BWNBX2PP303AW01

Отзывы:

Похожие инструкции для BWNBX2PP303AW01

Бренды по названию

Популярные бренды