8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Start Pulse Value
PLSE
This option allows the owner to program the value of the Start
Pulse if used for multiple pulses with an after-market central card
reader or pay system.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad until
Prog
appears in the display. Press the
START (enter) keypad, and
AtS
will appear in the display.
3. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to scroll through the programmable options until
PLSE
appears in the display.
4. When
PLSE
appears in the display, press the START (enter)
keypad. There are five digits in the Start Pulse Value. The
fifth digit will appear in the display and will flash one second
on, one second off.
5. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to increase or decrease the value of the fifth digit.
NOTE: The Start Pulse Value can be set from 1 to
65,535. The factory default setting is 25.
6. Press the START (enter) keypad to enter the fifth digit and
display remaining four digits. The active digit will flash one
second on and one second off.
NOTE: To go back to the current programmable op-
tion without changing the value, press the PERM
PRESS WARM (<) keypad.
7. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to increase or decrease the value of the active digit
and the START (enter) keypad to enter the value of the digit
and advance to the next digit.
8. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Cycle Length
CyCL
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad until
Prog
appears in the display. Press the
START (enter) keypad, and
AtS
will appear in the display.
3. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to scroll through the programmable options until
CyCL
appears in the display.
4. When
CyCL
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the PERM
PRESS WARM (<) keypad.
5. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to change the current value.
Value
Description
3
1 wash and 2 rinses
4
1 wash and 3 rinses
5
1 prewash, 1 wash, 3 rinses
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Default Cycle
dCyC
This option allows the owner to set the default cycle that the ma-
chine will enter when in the Ready Mode.
1. Control must be in Manual Mode. Refer to
2. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad until
Prog
appears in the display. Press the
START (enter) keypad, and
AtS
will appear in the display.
3. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to scroll through the programmable options until
dCyC
appears in the display.
4. When
dCyC
appears in the display, press the START (enter)
keypad. A number will appear in the display. Refer to table
below. This number corresponds to the current default cycle
value. The corresponding LEDs will also be lit.
Cycle
Display
NORMAL HOT
CyC1
NORMAL WARM
CyC2
NORMAL COLD
CyC3
PERM PRESS WARM
CyC4
DELICATES COLD
CyC5
Table 1
5. Press the NORMAL WARM (
∧
) or the DELICATES COLD
(
∨
) keypad to increase or decrease the current number to the
desired number.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
23
Part No. 805407R6
Содержание BFNBCASG113TN01
Страница 2: ......
