manualshive.com logo in svg

Alliance Laundry Systems AT170CSH, Руководство по обслуживанию

Поделиться
Скачать
Alliance Laundry Systems AT170CSH Скачать руководство пользователя страница 23

M413487

25

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

24. RELAY

(Manual Timer Models)
a. Remove four screws holding access panel to 

cabinet. Refer to Figure 1.

b. Lift access panel off top edge of front panel and 

pull panel forward. Refer to Figure 1.

c. Remove timer box cover. Refer to Figure 1.

d. Disconnect wires from relay.

e. Remove two screws holding relay to bracket. 

Refer to Figure 4.

NOTE: Refer to wiring diagram when rewiring 
relay.

Figure 3

T248PZ3C

DOOR

HANDLE

ACTUATOR

DOOR

HINGES

LOADING

DOOR

ASSEMBLY

TMB1496S

FRONT
PANEL 

ATTACHING

SCREWS

(6)

DOOR

HINGES

WASHER

HINGE

PIN

DOOR

HINGE

BRACKETS

HINGE

PIN

Содержание AT170CSH









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды