Allen-Bradley PowerFlex 527 Скачать руководство пользователя страница 56

Страница: 56 / 176

Rockwell Automation Publication 520-UM002B-EN-E - December 2017

Chapter 3

Configuring the PowerFlex 527 Drive with Integrated Motion

e. Enter the address of your EtherNet/IP module.

In this example, the last octet of the address is 1.

f. Click Change in the Module Definition area.

The Module Definition dialog box opens.

From the Time Sync Connection pull-down menu, choose Time Sync and
Motion.

10.

Click OK to close the Module Definition dialog box.

11.

Click Yes when prompted to confirm your module definition changes.

12.

Click OK to close the New Module dialog box.

Your new 1756-ENxT Ethernet
module appears under the I/O
configuration folder in the
Controller Organizer.

13.

From the Edit menu, choose Controller Properties.

The Controller Properties dialog box appears.

IMPORTANT

Time Sync functionality is what enables motion control on an Ethernet
network. Without this setting, you won’t be able to run your motion
application.

Содержание PowerFlex 527

















































































































































































Результаты поиска

Содержание PowerFlex 527

Отзывы:

Allen-Bradley PowerFlex 527, Руководство пользователя, Страница: 56 / 176

Результаты поиска

Содержание PowerFlex 527

Отзывы: