Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 135

Allen-Bradley PLC-5 MAP/OSI Скачать руководство пользователя страница 32

Chapter 3

MMS and Your Coprocessor

3-6

The MMS specification lists a set of data types, or formats, that your
variables are allowed to take. The data types allowed for your OSI
coprocessor are:

boolean
bitstring
integer
unsigned

integer

BCD
floating

point

visible

string

octet

string

generalized

time

structure
array

These data types directly correspond to areas in PLC controller memory
that contain data tables. These data tables store information, in different
data–type categories, that your application programs can access. The
following list shows the PLC–5 controller’s data tables you are allowed to
access through your applications:

ASCII

(A)

Binary

(B)

Signed

Word

(N)

Floating Point (F)
Timer

(T)

Counter

(C)

  Input Image (I)
  Output Image (O)
  Block Transfer Data (BT)
Control

(R)

Status

(S)

String

(ST)

  PID Control (PD)
  Message Control (MG)
  BCD Data (D)
  Sequential Function Chart (SC)
  Token Data (TD)

Important: Refer to your PLC–5 Programming Reference Manual for
descriptions of data type structures. See Appendix A of this manual for
more information on mapping MMS data types onto PLC–5 data files.

Mapping MMS Data Types

onto PLC-5 Controller Data

Files

«
...
30
31
32
33
34
...
»

Содержание PLC-5 MAP/OSI








































































































































Отзывы:

Нет отзывов