Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 101

Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 59

1761-6.5

Chapter

6

Setup, Programming, and Troubleshooting

DNI Software Files

Required Files

To configure the DNI as an I/O slave device on DeviceNet, you may need to
obtain two software files. These two files provide your network
configuration software with the information it needs to interface with the
DNI.

DNI Series A Information

RSNetWorx and DeviceNet Manager (version 3.0 and higher) include the
files necessary for DNI Series A.

DNI Series B Information

To configure the Series B DNI, you must have the Series B DNI EDS file
installed in your DeviceNet configuration software. RSNetWorx DeviceNet
Network Management software version 2.11.36 or higher includes all Series
B DNI files. You can also download the new files from http://www.ab.com/
micrologix. The following table shows the old and new file filenames:

1761-NET-DNI File Description

File Name

Series B

DNI Electronic Data Sheet

1761DNI3.EDS

DNI Configuration Software Utility

DNIUTIL1.EXE (Rev. 2.0 or higher)

DNI Icon for Configuration Software 1761DNI.ICO or 1761DNIB.BMP

Series A

DNI Electronic Data Sheet

1761DNI2.EDS

DNI Configuration Software Utility

DNIUTIL1.EXE

DNI Icon for Configuration Software 1761DNI.BMP

!

ATTENTION: DNI Series A configurations are not
compatible with DNI Series B. You must manually re-enter the
Series A parameters into the Series B DNI. This step is required
because of the enhanced functionality of DNI Series B.

Note:

DNI Series A stopped shipping in June of 1999. DNI Series B
started shipping in July of 1999.

«
...
57
58
59
60
61
...
»

Содержание DeviceNet 1761-NET-DNI






































































































Отзывы:

Нет отзывов