Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 101

Allen-Bradley DeviceNet 1761-NET-DNI Скачать руководство пользователя страница 42

1761-6.5

5-8

DNI Configuration Parameters and Programming Notes

Output Size

This parameter identifies the size, in words, of the data array that will be
written to the controller attached to the DNI’s RS-232 port. The array may
contain up to 16 (16-bit) words of data for DNI Series A (32 words for DNI
Series B) from a contiguous block within the attached controller.

The first byte (byte 0) of the first word contains the status byte and is not
available to the user. A sample of the data array is shown below:

Parameter

Type

Parameter Number

Description Range

Default Value

Series A Series B

I/O

8

6

Output Size

Series A: 1 to 16

Series B: 1 to 32

1

Important:

For DNI Series B, you must also configure the Output Split
Point. See page 5-9.

Word

Output Image

Series A Series B
0

0

Data (8 bits)

Status

1

1

Data Most Significant Byte (MSB) Data Least Significant Byte (LSB)

2

2

Data MSB

Data LSB

3

3

Data MSB

Data LSB

↓

↓

↓

↓

14

30

Data MSB

Data LSB

15

31

Data MSB

Data LSB

Note:

Byte 1 (MSB) of word 0 is available for user data.

Note:

For information on the Status Byte (byte 0), see the Status Byte
section on page 5-23.

«
...
40
41
42
43
44
...
»

Содержание DeviceNet 1761-NET-DNI






































































































Отзывы:

Нет отзывов