Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 28

Страница: 28 / 144

Publication 1756-UM050A-EN-P - December 2001

2-8

Installing the 1756-ENBT Module

Applying Chassis Power

Checking Power Supply
and Module Status

Check the LED indicators and alphanumeric display to determine if
the power supply and module are operating properly.

The alphanumeric display should cycle through the following states:
“TEST - PASS - OK - REV x.x,” where “x.x” is the module’s firmware
revision. The display then alternates between “OK” and the module’s
default BOOTP address.

If the alphanumeric display and LED indicators do not produce the
expected states refer to Appendix A for help in troubleshooting your
module.

What’s Next?

The following chapter describes some Ethernet basics you should
know before configuring your module.

31280-M

31281-M

LINK NET OK

OK indicator is

Power Supply

LINK

NET

red during self-test,

then green.

Alphanumeric

Indicator is GREEN

Display

Содержание ControlLogix 1756-ENBT
















































































































































Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды

Allen-Bradley ControlLogix 1756-ENBT, Руководство пользователя

Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды