Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 144

background image

Publication 1756-UM050A-EN-P - December 2001

About the 1756-ENBT Module

1-3

Rack optimized connections reduce the total number of connections
needed to transfer data when using many I/O modules in a system.
The following example illustrates the benefit of rack optimized
connections.

Assume you have set up a system that contains 10 discrete I/O
modules in a remote ControlLogix chassis. If you use direct
connections to transfer data to each of the these I/O modules, you
need 10 connections to transfer all of the data, one to each of the ten
I/O modules. If you use a rack-optimized connection to transfer the
data, you only need a single connection – the connection to the
1756-ENBT module.

See the

EtherNet/IP Performance and Application Guide

, publication

number ENET-AP001, for more information on connections.

Mixing Rack Optimized and Direct Connections

You can mix communication formats for different I/O modules in the
same chassis. I/O modules set up to use Rack Optimization will
communicate at the rate of the RPI (requested packet interval)
configured for the 1756-ENBT module. I/O modules configured for
direct communication will communicate at their set RPI and ignore the
1756-ENBT module’s RPI.

IMPORTANT

Although rack optimized connections offer an
efficient way to use resources, there are a few
limitations on their use:

•

You can only use rack optimized connections to
send data to and from discrete digital I/O
modules. Analog I/O requires direct connections.

•

Rack optimized connections can contain I/O data
and status information only. Additional module
information, such as diagnostics, is not available
through a rack-optimized connection.

•

All data is sent at the same time at the RPI rate of
the 1756-ENBT module.

«
...
15
16
17
18
19
...
»

Содержание ControlLogix 1756-ENBT

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ControlLogix 1756-ENBT

Бренд: Garmin Страницы: 4

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: Quectel Страницы: 90

Бренд: vacuubrand Страницы: 12

Бренд: Vacon Страницы: 47

ConferenceSHOT AV

Бренд: VADDIO Страницы: 114

Бренд: Vacon Страницы: 40

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Productivity 2000 P2-08NAS

Бренд: Automationdirect.com Страницы: 4

Бренд: Ezodo Страницы: 7

Бренд: Bentel Страницы: 88

Бренд: Zenith Страницы: 20

OBID ID ISC.ANT40/30

Бренд: Feig Electronic Страницы: 2

Бренд: Exhausto CDT Страницы: 16

Бренд: gefran Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды