Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 144

background image

Publication 1756-UM050A-EN-P - December 2001

1-2

About the 1756-ENBT Module

Hardware/Software
Compatibility

The 1756-ENBT module is compatible with the following product’s
firmware versions and software releases. Contact Rockwell
Automation if you need software or firmware upgrades to use this
equipment.:

What the Module Does

The 1756-ENBT module performs two primary tasks:

1.

Control of real time I/O data (also known as “implicit messaging”)
in conjunction with a Logix controller. The 1756-ENBT module may
serve as a bridge between I/O modules and the network, or as a
bridge between the controller and the network.

2.

Support of messaging data for configuration and programming
information, operator interfaces, etc. (also known as “explicit
messaging.”).

Support of Rack Optimized
and Direct Connections

The 1756-ENBT module supports both Rack Optimized and Direct
Connections. A direct connection is a real-time data transfer link
between the controller and the device that occupies the slot that the
configuration data references. A rack optimized connection is a
grouping of data from more than one I/O module into a single block
of data sent over a single connection.

Product

Firmware Version/
Software Release

1756-ENBT module

1.x or higher

1756-ENET/A/B

1.18 or higher

1794-AENT

1.x

Logix 5550 Controller

8.1 or higher

PanelView

All Ethernet compatible models

RSLogix 5000 software

8.1 or higher

RSLinx software

2.3 or higher

I/O

I/O

L
5

5
5

0

E
N
B
T

EtherNet/IP Network

E
N
B
T

I/O

I/O

E
N
B
T

I/O

I/O

E
N
B
T

«
...
14
15
16
17
18
...
»

Содержание ControlLogix 1756-ENBT

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для ControlLogix 1756-ENBT

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: CAME Страницы: 32

Бренд: HALDER Страницы: 2

coviva Smartbox TKP100A

Бренд: hager Страницы: 4

Бренд: Vag Страницы: 12

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Sanhua Страницы: 3

Бренд: rav Страницы: 120

Бренд: York Страницы: 20

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: Taoglas Страницы: 2

Бренд: We Care Solar Страницы: 46

Бренд: Watts Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды