Allen-Bradley ControlLogix 1756-ENBT Скачать руководство пользователя страница 110

Страница: 110 / 144

Publication 1756-UM050A-EN-P - December 2001

8-14

Interfacing with FLEX I/O

Download the Program to the Controller

To download the program to the controller do the following:

Click on the

Communications

menu and select

Who Active

The

Who Active

window will open (Your window will show the

drivers and devices you have installed).

Select your Ethernet driver (e.g., AB_ETH-1) and expand the tree
through the backplane of the local ControlLogix chassis.

Highlight the Logix 5550 controller and click on the

Download

button. You will see a message similar to the following:

Click on the

Download

button. The program will be downloaded

to the controller.

5. Minimize

RSLogix5000.

Содержание ControlLogix 1756-ENBT
















































































































































Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды

Allen-Bradley ControlLogix 1756-ENBT, Руководство пользователя

Результаты поиска

Содержание ControlLogix 1756-ENBT

Отзывы:

Похожие инструкции для ControlLogix 1756-ENBT

Бренды по названию

Популярные бренды