Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 87

Страница: 87 / 116

Publication 1769-UM005A-EN-P

Appendix

Module Addressing and Programming with
MicroLogix 1500 and RSLogix 500

Module Addressing

The module uses eight input words for data and status bits (input image),
and seven configuration words.

For example, to obtain the general status of channel 2 of the module
located in slot e, use address I:e.6/2.

Channel 0 Data Word

Word 0
Word 1
Word 2
Word 3

Word 4

Word 5

Channel 1 Data Word
Channel 2 Data Word
Channel 3 Data Word

General/Open-Circuit Status Bits

Over-/Under-range Bits

Channel 0 Configuration Word
Channel 1 Configuration Word
Channel 2 Configuration Word
Channel 3 Configuration Word

I:e.0
I:e.1

I:e.2

I:e.3
I:e.4
I:e.5

Word 0
Word 1
Word 2
Word 3

Address

Input Image

8 words

Configuration

File

7 words

slot e

Input Image

File

Configuration

File

Memory Map

Bit 15

Bit 0

Refer to your
controller
manual for the
addresses.

Channel 3 Data Word
Channel 3 Data Word

Word6

Word 7

I:e.6
I:e.7

Channel 4 Configuration Word
Channel 5 Configuration Word

Word 4
Word 5

Module Configuration Word

Word 6

I:e.6/2

Input File Type

Slot

Word

Bit

Bit Delimiter

Word Delimiter

Element Delimiter

AB PLCs

Содержание Compact 1769-IR6





















































































































Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды

Allen-Bradley Compact 1769-IR6, Руководство пользователя

Результаты поиска

Содержание Compact 1769-IR6

Отзывы:

Похожие инструкции для Compact 1769-IR6

Бренды по названию

Популярные бренды