Allen-Bradley Compact 1769-IR6 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 116

background image

Publication 1769-UM005A-EN-P

Module Data, Status, and Channel Configuration

4-17

Channel Cutoff Frequency

The channel cutoff frequency (-3 dB) is the point on the input channel
frequency response curve where frequency components of the input
signal are passed with 3 dB of attenuation. The following table shows
cutoff frequencies for the supported filters.

All frequency components at or below the cutoff frequency are passed by
the digital filter with less than 3 dB of attenuation. All frequency
components above the cutoff frequency are increasingly attenuated, as
shown in the graphs below for several of the input filter frequencies.

Table 4.8 Filter Frequency vs. Channel Cutoff Frequency

Filter Frequency

Channel Cutoff Frequency

10 Hz

2.62 Hz

50 Hz

13.1 Hz

60 Hz

15.7 Hz

250 Hz

65.5 Hz

500 Hz

131 Hz

1 kHz

262 Hz

NOTE

Channel cutoff frequency should not be confused with
channel update time. The cutoff frequency simply
determines how the digital filter attenuates frequency
components of the input signal. See Determining Module
Update Time on page 4-26.

«
...
55
56
57
58
59
...
»

Содержание Compact 1769-IR6





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Compact 1769-IR6

Бренд: Harmar Mobility Страницы: 16

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 13

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: Midland Страницы: 75

Бренд: Optimus Страницы: 2

Бренд: urmet domus Страницы: 30

Бренд: CAME Страницы: 32

Бренд: M-system Страницы: 7

Бренд: salmson Страницы: 16

Бренд: Commax Страницы: 10

Бренд: National Instruments Страницы: 151

Бренд: Farfisa Страницы: 36

Бренд: Goodmans Страницы: 22

AutoLift AL-6000S2

Бренд: AAQ Страницы: 36

PIO-32/32RL(PCI)H

Бренд: Contec Страницы: 4

Бренд: NAIM Страницы: 31

Бренд: Grundig Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды