Allen-Bradley 9300-Rades Скачать руководство пользователя страница 10

LED Status 
 

Modem LEDs 

LED 

LED Activity 

LED Definition 

Trouble-
shooting 

Flashing Orange 

Communicating 

TX-Transmit 
 

Out Not 

Communicating 

No Action 
needed 

Flashing Orange 

Communicating 

RX-Receive 

Out Not 

Communicating 

No Action 
needed 

Green 

Signal to the connected 
device that the modem 
is ready to receive data.  
CS is set to on by 
default.  This signal is an 
output of the modem. 

No Action 
needed 

CS- 
Clear to Send  
(CTS) 

Out 

Modem is not ready to 
receive 

Do a factory 
reset of the 
modem 

Green 

Signal is an input to the 
modem.  Device is ready 
to receive data from the 
modem 

No Action 
needed 

RS- 
Request to 
Send 
(RTS) 

Out 

No Handshaking is 
being used or device is 
not communicating with 
the modem 

No Action 
needed 

Green 

DCD signal: modem 
connected 

No Action 
needed 

CD- 
Carrier Detect 
(DCD) 

Out 

Modem is off-line 

No Action 
needed 

Green 

DTR signal: modem 
connected 

No Action 
needed 

TR- 
Data Terminal 
Ready 
(DTR) 

Out 

No DTR signal coming 
from the connected 
device 

No Action 
needed 

Green 

On-line: Originated Call 
 
Off-line: Automatic 
Answer on 

AA should be 
on while off-
line.  If not, 
verify that 
S0>0 

AA- 
Auto-Answer 

Out 

On-line: Answered Call 
 
Off-line: Incoming Ring 

No Action 
needed 

 

10

Содержание 9300-Rades













Отзывы: