manualshive.com logo in svg

Allen-Bradley 8720MC, Руководство пользователя, Страница: 71 / 128

Поделиться
Скачать
Allen-Bradley 8720MC Скачать руководство пользователя страница 71

Rockwell Automation Publication 8720MC-RM001K-EN-P - September 2018

71

Connect the 8720MC-RPS Unit

Chapter 5

Install Ribbon Cables

For a single units or for leader unit when multiple units are connected in 
parallel, the regulator board is connected to the power interface board (PIFS) 
with a ribbon cable. Also, ribbon cable is used for connecting between the 
power interface boards of the leader unit and the follower unit and between the 
power interface boards of the follower units.

• Ribbon cable connects between the regulator board (BDSR) and power 

interface board (PIFS)

• Ribbon cable connects between power interface boards (PIFS).

Figure 39 - Connecting Ribbon Cables (series #)

Figure 40 - Connecting Ribbon Cables (series B)

BDSR

PIFS

CN1

CN2

CN1

CN2

CN3

Unit 1 (leader unit)

Unit 2 (follower unit 1)

Unit 3 (follower unit 2)

PIFS

CN1

CN2

CN3

PIFS

CN1

CN2

CN3

Parallel Connection

of 3 Units

(8720MC-RPS065BS or 8720MC-RPS190BS)

Parallel Connection

of 2 Units

(8720MC-RPS065BS or 8720MC-RPS190BS)

Single Unit

(8720MC-RPS065BS or 8720MC-RPS190BS)

RST PRG ENT

㻾㻱㻭㻰㼅

㻲㻭㼁㻸㼀

㻼㻾㻻㻳㻾㻭㻹

㻭

㼂

㼗㼃

Regulator Board (BDSR)

PIFS

3

N

C

2

N

C

CN1

Unit 1 (leader unit)

Unit 2 (follower unit  1)

Unit 3 (follower unit 2)

Parallel Connection

of 3 Units

(8720MC-RPS065BS or 8720MC-RPS190BS)

PIFS

3

N

C

2

N

C

CN1

PIFS

CN2

CN3

CN1

CN2

CN1

Parallel Connection

of 2 Units

(8720MC-RPS065BS or 8720MC-RPS190BS)

Single Unit

(8720MC-RPS065BS or 8720MC-RPS190BS)

Содержание 8720MC

































































































































Отзывы:

Нет отзывов