Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 296

Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 98

98

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 3

Input Module Features

Pulse Latching

You can use Pulse Latching to detect or latch short duration pulses. The
module can detect incoming pulses with a duration as short as 10 μs if the
frequency is under 4 kHz (period of 250 μs).

Pulse Latching is supported via the Timestamping feature and Timestamp
Latching.

To use Pulse Latching, you must complete the following:

• On the Module Definition dialog box in the Logix Designer application

project, set the Input Data parameter to Timestamp Data.

• Enable COS for the input point where a latch of short duration pulses is

needed. You can enable COS in the following ways.

COS is disabled by default on all points.

When the module detects a short duration pulse at an input point, the changes
that are described in this table occur.

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

ow

er

MOD P

ow

er

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

OK

RUN

FORCE

FAN 1

SD

FAN 2

Compact

Logix

5480

B1

A1

1

2

A2

5069-L46ERMW

CONTROLLER

UPS

MP

SA

R
B
F

R

B

F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

The following Compact 5000 I/O standard input modules support
Pulse Latching:

• 5069-IB16F

• 5069-IB6F-3W

Location in Logix Designer Application

Action

Module Properties dialog box > Points category >
Ptxx subcategory

Check the input transition type where you need to
latch short duration pulses.
For example, if you need short duration pulses
latched for Off to On transitions, check Off -> On
Input Transition.

Module tags

One or both of the following:
• Change the C.Ptxx.CaptureOffOnEn tag to 1.
• Change the C.Ptxx.CaptureOnOffEn tag to 1.

Input Transition Type
Where Pulse Is Captured

Change in Logix Designer Project

Off to On

• The I.Ptxx.TimestampOffOnNumber tag increments.

• The timestamp is recorded in I.Ptxx.TimestampOffOn tag.

On to Off

• The I.Ptxx.TimestampOnOffNumber tag increments.

• The timestamp is recorded in I.Ptxx.TimestampOnOff tag.

«
...
96
97
98
99
100
...
»

Содержание 5069-IA16









































































































































































































































































































Отзывы:

Нет отзывов