Allen-Bradley 5069-IA16 Скачать руководство пользователя страница 187

Страница: 187 / 296

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

187

Configure a Standard Module

Chapter 6

Edit 5069-OW16 Module
Configuration Categories

In addition to the General, Connection, and Module Info categories, the
Points category is available when you configure a 5069-OW16 module.

Points Category

The Points category shows the configuration options available for each point.
You can configure the following parameters from the Points category:

• Output State During Program Mode

• Output State During Fault Mode

• Fault Mode Output State Duration

• Fault Mode Output State Final State

• Output State When Communications Fail in Program Mode

IMPORTANT

If you use the Listen Only connection type, the Points Category does
not appear.

Содержание 5069-IA16









































































































































































































































































































Результаты поиска

Содержание 5069-IA16

Отзывы:

Allen-Bradley 5069-IA16, Руководство пользователя, Страница: 187 / 296

Результаты поиска

Содержание 5069-IA16

Отзывы: