Allen-Bradley 5069-IA16 Скачать руководство пользователя

Страница: 155 / 296

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

155

Configure a Standard Module

Chapter 6

Discover Remote I/O Modules

To use the Discover Modules method with remote I/O modules, complete the
following steps.

1. Go online with your Logix Designer application.

The project must include a Compact 5000 I/O EtherNet/IP adapter.

2. Right-click the Compact 5000 I/O EtherNet/IP adapter and choose

Discover Modules.

The Logix Designer application automatically detects available modules
that are connected to the backplane.

3. At the Select Module Type window, click Create to add the discovered

module to your project.

Содержание 5069-IA16









































































































































































































































































































Результаты поиска

Содержание 5069-IA16

Отзывы:

Похожие инструкции для 5069-IA16

Бренды по названию

Популярные бренды

Allen-Bradley 5069-IA16, Руководство пользователя

Результаты поиска

Содержание 5069-IA16

Отзывы:

Похожие инструкции для 5069-IA16

Бренды по названию

Популярные бренды