Allen-Bradley 193-DNENCAT Скачать руководство пользователя страница 27

Страница: 27 / 112

Rockwell Automation Publication 193-UM014C-EN-P - August 2016

Configure the EtherNet/IP Communication Auxiliary Module

Chapter 2

DNS Addressing

To further qualify a module’s address, use DNS addressing to specify a host

name for a module. This also includes specifying a domain name and DNS

servers. DNS addressing makes it possible to set up similar network structures

and IP address sequences under different domains.

DNS addressing is only necessary if you refer to the module by host name, such

as in path descriptions in MSG instructions.

To use DNS addressing, perform this procedure.

1. Assign a host name to the module.

2. Configure the module's parameters.
3. In addition to the IP address, subnet mask, and gateway address,

configure a host name for the module, domain name, and primary/

secondary DNS server addresses.

Electronic Data Sheet (EDS)

File Installation

Before the EtherNet/IP communication auxiliary module is configured to

communicate on an EtherNet/IP network, it must be registered to the software

that configures the network (for example, Rockwell Automation RSLinx

Classic and RSNetWorx for EtherNet/IP software). You register the module by

installing an EDS file. You can obtain the EDS file for the EtherNet/IP

communication auxiliary module from one of two locations:

• embedded in the module

• the Allen-Bradley EDS file download website.

Download the EDS File

Embedded in the Module

The EDS file for the EtherNet/IP communication auxiliary module is

embedded within the module. After the IP address for the module has been

configured, connect the module to same Ethernet network as a personal

computer. Using a web browser on the personal computer, you can download

the EDS file using a web browser by following these steps:

NOTE:

Contact the network administrator to have a host name assigned. Valid host names should

comply with IEC-1131-3.

TIP

When using Firmware revision 3.000 and higher, see

page 33

for instructions

on how to commission the EtherNet/IP communication auxiliary module and
enable use of the embedded web page.

Содержание 193-DNENCAT

















































































































Результаты поиска

Содержание 193-DNENCAT

Отзывы:

Allen-Bradley 193-DNENCAT, Руководство пользователя, Страница: 27 / 112

Результаты поиска

Содержание 193-DNENCAT

Отзывы: