Allen-Bradley 1788-CN2FFR Скачать руководство пользователя страница 48

Страница: 48 / 104

Rockwell Automation Publication 1788-UM057B-EN-P - September 2014

Chapter 2

Set Up in the Studio 5000 Logix Designer Application

MultiMaster Connecting
Procedures

To avoid communication loss, or a field device going to the visitor address range,
follow the MultiMaster connection procedures in this section.

Connect Safe Mode

The Connect Safe mode is used in the

Reconnect Two Separate Running LAS

Devices on page 47

and

Swap Out Linking Devices on page 47

procedures.

To enter the

Connect Safe mode,

hold the Page button for at least 5 seconds.

The LCD displays the time until communication is re-established to the linking
device (10 seconds).

Figure 8 - Location of the Page Button for Connect Safe Mode

Start the Back-up LAS Master (Already Configured)

Follow these steps to start the Back-up LAS master.

Plug in all communication connectors (H1, EtherNet/IP or ControlNet
cables), but not the power.

Once all communication connectors are plugged in, connect the power to
the linking device.

The linking device starts in Back-up LAS mode and does not disturb
communication.

Содержание 1788-CN2FFR









































































































Результаты поиска

Содержание 1788-CN2FFR

Отзывы:

Allen-Bradley 1788-CN2FFR, Руководство пользователя, Страница: 48 / 104

Результаты поиска

Содержание 1788-CN2FFR

Отзывы: