Allen-Bradley 1771-P4R Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

Allen-Bradley 1771-P4R Скачать руководство пользователя страница 1

Power Supply Modules

(Cat. No. 1771P4R and P6R)

Installation Data

1

AllenBradley

Redundant Power Supplies

(Cat. No. 1771-P4R and 1771-P6R)

Installation Data

This document provides you with the following information:

what this package contains
tasks on installing your power supply module
how to interpret indicators
flow charts for troubleshooting your power supply module

When you receive your 1771-P4R or -P6R power supply, you should see
the following in the box:

one 1771-P4R or 1771-P6R power supply module
one 3-position terminal block (attached to module)
one 5-position terminal block (attached to module)
one redundant cable

To install your power supply module you need to know how to perform the
following tasks:

set the jumpers
set the I.D. selection and configuration switches
place the power supplies
connect the redundancy cables
wire the alarm relay
connect input power

To the Installer

What This Power Supply

Package Contains

Installing the Power Supply

Module

1
2
3
...
»

Содержание 1771-P4R

















Отзывы:

Нет отзывов