Allen-Bradley 1757-FFLD2 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 184

background image

Rockwell Automation Publication 1757-UM012A-EN-P - July 2011

55

Create an RSFieldbus Software Project

Chapter

3

Use Tools for Function
Block Characterization

You have tools that provide access to the value and status of a block parameter as
well as let you make configurations both offline and online. You must save the
configuration upon closing, especially when online. If you ignore the prompt
warning to save, and do not save the changes, the configuration file will not have
the same values as the changes made in the device.

Table 3 - Function Block Characterization Toolbar

Toolbar Icon

Description

Displays input parameters. An input parameter obtains its value from a source
external to the block.

Displays output parameters. An output parameter may be linked to an Input
Parameter of another block.

Displays contained parameters. A contained parameter is a parameter whose value
is configured, calculated, or set by an operator or higher level device.

Displays dynamic parameters. Dynamic parameters values are calculated by the
block algorithm and therefore do not need to be restored after a power failure.

Displays diagnostic parameters.

Displays service parameters.

Displays operating parameters.

Displays alarm parameters. Alarms and events (alerts) represent state changes
within block applications.

Displays tune parameters.

Displays the local parameters.

If this icon is pressed, you must click End Edit to complete an edit in this dialog box.
If it is not pressed, you can click another line in the dialog box to complete the edit.

Displays the Relative Index column.

Displays the Handling column, which shows read/write permission.

Displays the parameters for the block filter by the user customization.

Use this icon

only in the online dialog box

to save changes made in

online mode.

Toggles the Value display between a symbol and a numeric value.

Displays help information from the DD at the bottom of the Characterization
dialog box.

«
...
53
54
55
56
57
...
»

Содержание 1757-FFLD2

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1757-FFLD2

Бренд: GRAUPNER Страницы: 180

Бренд: Parker Страницы: 58

Бренд: MPMan Страницы: 32

Бренд: Bose Страницы: 2

Бренд: DC-Connex Страницы: 16

Бренд: ICT Страницы: 11

Бренд: Grundig Страницы: 34

Бренд: Belson Страницы: 34

Бренд: Gamma Vacuum Страницы: 43

Бренд: SoundMax Страницы: 43

Meridian Norstar

Бренд: Nortel Страницы: 18

Бренд: Panasonic Страницы: 24

MICHELANGELO BT A 60

Бренд: BFT Страницы: 84

Бренд: GE Страницы: 8

Бренд: GE Страницы: 12

Бренд: Raven Страницы: 59

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды