Allen-Bradley 1734-IB8S Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 156

Allen-Bradley 1734-IB8S Скачать руководство пользователя страница 29

Rockwell Automation Publication 1734-UM013C-EN-P - August 2010

29

Safety Functions

Chapter

2

Dual-channel Setting

When the data of both channels is in the on state, and neither channel has a fault,
the outputs are turned on. The status is normal. If a fault is detected on one
channel, the safety output data and individual safety output status turn off for
both channels.

Figure 13 - Dual-channel Setting (not to scale)

Safety Output Fault Recovery

If a fault is detected, the safety outputs are switched off and remain in the off
state. Follow this procedure to activate the safety output data again.

1.

Remove the cause of the error.

2.

Command the safety output (or safety outputs) into the safety state.

3.

Allow the output-error latch time to elapse.

After these steps are completed, the I/O indicator (red) turns off.
The output data can now be controlled.

IMPORTANT

Stuck high faults require a module power reset to clear
the error.

ON

OFF

OUT0

Safety Output
Status 0, 1

OUT0

OUT1

OUT1

Safety Output
Status 0, 1

Fault Detection

Error
Detected

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

Normal Operation

Safety
I/O
Network
Data Sent
to the
Controller

Safety
I/O
Network
Data Sent
to the
Controller

«
...
27
28
29
30
31
...
»

Содержание 1734-IB8S





























































































































































Отзывы:

Нет отзывов