manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 94 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 94

94

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

Chapter 6

Replace Guard I/O Modules

Reset the Module to Out-of-
box Configuration

If a Guard I/O module was used previously, clear the existing configuration 
before installing it on a safety network.

When the programming software is online, the Safety tab of the Module 
Properties dialog box displays the current configuration ownership. When the 
opened project owns the configuration, Local is displayed. When a second 
device owns the configuration, Remote is displayed, along with the safety 
network number (SNN), and node address or slot number of the configuration 
owner. Communication error is displayed if the module read fails.

If the connection is Local, you must inhibit the module connection before you 
reset ownership. To inhibit the module:

1. Right-click the module and choose Properties.

2. Click the Connection tab.

3. Check the inhibit module checkbox.

4. Click Apply and then OK.

Follow these steps to reset the module to its out-of-box configuration when 
online.

1. Right-click the module and choose Properties.

2. Click the Safety tab.

3. Click Reset Ownership.

Replace a Module in a 
GuardLogix System

The replacement of safety devices requires that the replacement device is 
configured properly and that the operation of the replacement device is user-
verified.

Two options for I/O device replacement are available on the Safety tab of the 
Controller Properties dialog box in the programming software:

• Configure Only When No Safety Signature Exists
• Configure  Always

ATTENTION: 

During replacement or functional testing of a device, the safety 

of the system must not rely on any portion of the affected device.

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов