manualshive.com logo in svg

Allen-Bradley 1732ES-IB12XOB4, Руководство пользователя, Страница: 43 / 176

Поделиться
Скачать
Allen-Bradley 1732ES-IB12XOB4 Скачать руководство пользователя страница 43

Rockwell Automation Publication 1791ES-UM001G-EN-P - November 2016

43

Install the Module

Chapter 3

ATTENTION: 

 Wiring Guidelines

• Disconnect the module from the power supply before wiring or connecting 

cables. Devices connected to the module can operate unexpectedly if wiring 
is performed while power is supplied.

• Wire correctly after confirming the signal names of all terminals.

• Wire the Guard I/O™ modules properly so that 24V DC line does not touch 

the safety outputs accidentally or unintentionally.

• Do not route communication, input, or output wiring with conduit 

containing high voltage. Refer to Industrial Automation Wiring and 
Grounding Guidelines, publication

 1770-4.1

.

• Wire conductors correctly and verify operation of the module before placing 

the system into operation. Incorrect wiring can lead to loss of safety 
function.

ATTENTION: 

Be Aware of Safety Requirements

Personnel responsible for the application of safety-related programmable 
electronic systems (PES) shall be aware of the safety requirements in the 
application of the system and shall be trained in using the system.

ATTENTION: 

Electrical Safety Considerations

To comply with the CE Low Voltage Directive (LVD), all connections to this 
equipment must be powered from a source compliant with the following:

• Safety Extra Low Voltage (SELV) Supply.

• Protected Extra Low Voltage (PELV) Supply.

If the devices (sensors) connected to the input connections require Class 2 
power to operate, the auxiliary power connections of this equipment must be 
powered by a Class 2 source.

ATTENTION: 

 Maintain IP Rating for 1732ES Modules

Make sure all connectors and caps on 1732ES modules are securely tightened to 
properly seal the connections against leaks and maintain IP enclosure type 
requirements.

Applicable only to 1732ES modules.

Содержание 1732ES-IB12XOB4

















































































































































































Отзывы:

Нет отзывов